The Cedar Shake & Shingle Bureau prefers the use of nails, however if you choose to use staples they must be stainless steel Type 316 in locations within fifteen (15) miles of salt water. … 10″ require 2 additional staples and these two staples are driven approximately 1″ apart near the center of the shingle.
Can I use 1/4 crown staples for cedar shingles?
The following are a few recommendations to help ensure their lasting beauty. Exposure: To prevent buckling, use a 5” (12.7 cm) maximum exposure. Fasteners: Rust-resistant (galvanized, aluminum or stainless) nails or staples, 1 1/4” to 1 1/2” (3.2 to 3.8 cm) long.
Can you staple into shingles?
Staples damage your shingles. Even the tiniest holes in your shingles are big enough for water to gradually seep in and make its way into the vulnerable parts of your roofing. … Tiny holes from repeated stapling will limit the lifespan of your roof considerably.
Can you use galvanized staples for cedar shingles?
In double course applications, the exposed Certi-label Western Cedar shingle or shake shall be face-nailed with two hot-dipped galvanized or stainless steel casing nails, driven 2″ above the butt line, and 3/4″ from each edge.What type of fastener do you use on cedar shingles?
The Cedar Shake & Shingle Bureau prefers the use of nails, however if you choose to use staples they must be stainless steel Type 316 in locations within fifteen (15) miles of salt water. For locations outside of the salt water zone – stainless steel staples Type 304 or Type 316 must be used.
Do cedar shingles need to be sealed?
No. Never seal your cedar roof. Sealing the roof will lock in moisture that would otherwise naturally evaporate during normal weather conditions. Cedar needs to breathe and thus a water repellant type product, rather than a water proofer is the best route to follow.
Do you nail or staple shingles?
Fasteners for asphalt shingles should be roofing nails or staples. The head of a roofing nail or the crown of a staple is what actually holds a shingle in place. … If staples are properly installed, they offer nearly the same wind resistance as nails.
Can you use electro galvanized staples outside?
They are the only staples we would highly recommend for outdoor and marine projects. Galvanized steel staples are made of steel and then coated with a layer of zinc to help guard against general corrosion. … If exposed to excessive moisture, especially saltwater, galvanized steel staples may rust over time.What size staples cedar shingles?
According to my research, there are two best-practice options: shingle nails or air-driven staples measuring 7/16” wide. Stainless steel fasteners are always optimal for exterior applications because they never rust, but finding shingle-friendly fasteners in these configurations isn’t easy.
What size nails do you use for cedar siding?Siding TypeThickness (in.)Nail SizeBevel3/42-1/4 (7d)7/8 & greater3 (10d)Boards, Tongue & Groove, and Channel5/82 (6d)3/42 (6d)
Article first time published onCan you staple your roof?
“Any penetration through your roofing materials can lead to damaging leaks.” Not only will staples damage your home, you could also damage the lights. One staple misfire can ruin an entire strand of lights. So, the first rule for safe decorating: Put down the staple gun.
Can you use a staple gun on your roof?
Works well for underlayments: When it comes to securing roof underlayments, such as roofing tar paper, staples get the job done with precision and durability. Less prone to jamming: Staple guns often jam up less than nail guns, which means that you can complete the project quickly.
Can you use a staple gun for roofing felt?
Tack the roofing felt down with 1/4″ staples using an air compressor with a pneumatic stapler, a hammer-tacker, or a staple gun every 12 inches.
Can you use brad nails for cedar shingles?
A regular brad nailer? … That will make our task easy as we will only need to identify a nail gun that shoots the accepted nails.. Now, here is what the CSSB says about fasteners for cedar shingles: “Use either rust-resistant staples or shingle nails (1-1/4” to 1-1/2” long), galvanized, in stainless steel or aluminum”.
How much do you overlap cedar shingles?
Cedar shingles should lap at least 18 cm (7 in.) over each side of valley flashing.
How do you keep cedar shingles looking new?
If you have weathered and discolored wood siding, you can regain the new look of cedar by cleaning off the dirt and mildew with a solution of one third cup liquid household detergent (be sure it is ammonia-free), one quart liquid household bleach (containing 5% sodium hypochlorite), and three quarts warm water.
How long do cedar shingles last?
As long as it’s properly installed and with proper maintenance, you can expect to get 30 years of life out of your cedar shake roof. If you invest in quality materials and live in an area with the right conditions, you could possibly get up to 50 years out of it.
Why is hand nailing shingles better?
Hand driving nails into shingles allows for the roofer to place the nail on the proper nail line and then drive the nail in. Ensuring that the nails are properly placed each and every time because the head of the hammer stops flush on top of the shingles.
What nails do you use for shingles?
Galvanized roofing nails tend to resist rust formation, and they are a suitable option for asphalt shingles. Owens Corning requires using either galvanized steel, stainless steel, or aluminum nails to affix shingles.
What size nails do you use for shingles?
If you’re using typical architectural shingles and 3/8-inch-thick sheathing, you’ll need 1‐inch nails. If your building codes require thicker sheathing, you’ll need 1 ¼-inch nails. When installing thicker shingles, you may need to use a longer nail in order to penetrate the OSB beneath fully.
Can you walk on cedar shingles?
So can you walk on a cedar shake roof? The short answer: yes. … Still, even if they do support your weight, cedar shakes are also notoriously slippery and difficult to navigate, especially after a recent storm or if they are covered in moss or other growths.
Should you treat cedar shakes?
Without treatments, cedar shakes can degrade over time, with constant exposure to the sun’s UV rays, the elements, and water, of course. It also means that the cedar shakes can suffer from fungus and algae growth without proper treatment. Most importantly, without treatment, cedar shake shingles can catch on fire.
Is linseed oil good for cedar shingles?
Some cedar siding shingles are treated with bleaching oil, which is a treatment made with linseed oil and bleach crystals. Along with protecting your cedar shingles against decay and other coastal contamination, this treatment will also give them the weathered silvery gray look that many homeowners prefer.
Should you stain cedar shakes?
Staining cedar shingles not only enhances their beauty but also fortifies them against threats posed by the elements. … To protect new shingles, apply a penetrating stain. Stain soaks in and protects the wood from the weather, and it won’t crack, peel, or chip.
How do you fix warped cedar shingles?
If you have a warped shingle, there are a couple ways to fix this problem. First, you can put in some long screws, reinforcing the shingle to the roof and minimize the damage caused by warping. Another, and more complicated, option is to remove the shingle and shorten it.
Can you use a finish nailer for cedar siding?
The answer is, yes. Framing nail guns can be used for siding installation, if the nail being used is long enough to attach the siding firmly to your exterior wood sheathing.
What is a crown stapler?
A crown stapler is essentially a staple gun. It uses staples instead of nails, which is what is used by a nail gun. … It is a permanent fastening solution that uses staples with a round or flat head. This allows for a strong hold when fastening material to a wood surface such as upholstery.
What do roof nails look like?
All roofing nails have wide, flat heads and short shanks. The tips of the nails are sharp and pointed for easy insertion so you don’t break the shingles or damage the wood when driving the nails through. Different roofing materials require different types of roofing nails.
What are electro galvanized staples?
Electro Galvanized Staples are plated with a layer of zinc bonded to the steel to protect against corrosion. The smooth shiny finish is generally used in areas where minimal corrosion resistance is needed. 9 ga 1/4 in head. Use to fasten wire and fencing to wood posts.
What are Galvanised Staples?
Galvanised staples are suitable for use indoors and outdoors as they are coated with zinc to protect them from corrosion, which means that they are usually water and weatherproof. The are designed to withstand wet conditions without rusting, making them ideal for garden jobs.
How long do galvanized staples last?
Ideal for indoor applications, the EG coating has an average lifespan of 5-10+ years depending on the environment. Similar to HDG, Electro-Galvanized nails are also bathed in zinc, but with an electric current that charges the zinc acid and attaches it to the nail’s body.
