Can you spur a light off a socket

You need the neutral to make the light work but you can take a spur from the socket underneath the desk for a light, you could place a FCU next to socket underneath desk then run cable to light switch and then on to light fitting .. you cannot run spur to spur with sockets incase of over load of cable but a light is …

Can you run a light off a plug socket?

Can I spur off a spur?

There is no problem in spurring off a fused spur (I think that’s what you mean). The principle is you just need to protect the cable. This week I’ve seen a unfused spur from a socket on the ring to a single socket (in 2.5 6262Y) – then from the single socket to a FCU in 1.5 6242Y for the boiler.

Can I run a spur off a socket?

The easiest way of connecting into a ring circuit is to run a spur cable from the terminals of an existing socket – but you can’t connect it to any socket. The IEE Wiring Regulations are very specific about this. You mustn’t run a spur from a socket that’s already on a spur, or that already supplies a spur.

Can I spur off an outside light?

It’s fine. Put in a DP FCU before the light/pir and fuse down accordingly.

Can I put 2 double sockets on a spur?

you can have maximum one double socket as a normal spur but if you are going from socket to FCU fused at 13 amp from there you can add as many sockets as you wish as all the sockets and cable will be protected by the fuse so no chance of overloading the cable the fuse will blow first.

How many times can you spur off a socket?

A spur can be connected to an existing socket, on either a ring main or a radial circuit, providing that socket does not already have a spur. That is only one spur per socket is allowed and the number of spurs must not exceed the number of sockets.

Can you run a fused spur off a fused spur?

You can but you may risk overloading that spur causing the 13a fuse to blow what is your intended use for your garage sockets and your conservatory.

Can I use a plug instead of a fused spur?

“The regulations state that the appliance needs to be fused, either with a plug or a fused spur. … So as long as the plug sockets are accessible without touching the appliance to turn it off then this is fine, but also a fused spur is fine too.”

Can I use a fused spur as a light switch?

How to Wire a Light Switch from a Fused Spur. … Choose a spur with a suitable current rating – normally 3 or 5 amps for a light switch. You can install either a switched fused spur, which will also function as the on-off button or an unswitched fused spur alongside a conventional light switch.

Article first time published on

Why can't you run a spur off a spur?

The reason for not running two spurs from the same spur “point” is that it can lead to possible overloads in that one leg of the final can become unbalanced and exceed the max.

Why is there only one spur on a socket?

The limit of one spur per point is if the point which is spurred off is UNFUSED. If you fuse it to 13A you can put as many as you want on it. The reason I explained was that standard final ring circuits wired in 2.5mm2 T&E are designed such that any point on the ring will not be loaded above 20A for an extended period.

Is adding a spur notifiable?

Some minor electrical work will not be notifiable (see above). Examples include adding a lighting or power point to an existing circuit, adding a spur to an existing circuit or replacing a light fitting.

Can I use 1.5 cable for sockets?

Depending on the installation method used, the 1.5mm cable has a maximum rated capacity of between 14 and 20 amps, so its right on the limit. … The only solutions are to upgrade the cable to 2.5mm or downgrade the MCB to 10amps.

What is an unswitched fused spur used for?

An unswitched fused connection unit could be used for any appliance that has its own ON/OFF switch, such as a washing machine, or a device that operates continuously and must be difficult to turn off, such as a fire alarm or security lights.

Can I install a fused spur myself?

As long as the job isn’t within a ‘special location’ such as a bathroom or outdoors, you’re also allowed to install additional new light fittings, switches, sockets and even add a single fused spur to an existing circuit (a ‘spur’ is a new cable and socket run as a branch from an existing socket on the ring main).

How many 13 amp sockets can a ring main have?

The IET Wiring Regulations (BS 7671) permit an unlimited number of 13A socket outlets (at any point unfused single or double, or any number fused) to be installed on a ring circuit, provided that the floor area served does not exceed 100 m2.

Can you run a washing machine off a spur?

A spur off a ring circuit in a kitchen powers both washing machine and a dishwasher. … One of these twin sockets is mounted at low level and is used to supply a dishwasher (2.4kW rating) and a washing machine (1.5kW rating) connected via 13A plugs.

Does a washing machine need a fused spur?

Fused spurs are commonly used as an alternative to a conventional socket, for the installation of powerful electrical appliances that can be installed without a plug, such as ovens, washing machines, electric heaters, dishwashers, fridges, and so on. …

Can you plug electric cooker into normal socket?

Save time & money – No hard wiring or electrician needed. Most of the ovens we sell can be plugged into a normal wall socket with a 13a plug and some ovens have a plug already fitted. If you want to check then look for the data badge on the oven and if the total power is less than 3000 watts then it’s fine to plug in.

Can you have 2 fused spurs off one socket?

Only one fused spur may be taken from any socket on a ring. From that fused spur you can have as many electrical outlets as you like, as they are then protected by the fuse.

Can you turn a plug socket into a light switch?

Adding an electrical outlet next to an existing light switch is easy, as long as there is a neutral wire in the box. … If there is a bundle of two white wires tied together behind the switch and two separate wires running to the switch, it will be easy to add an outlet.

How many sockets can you have after a fused spur?

Non-fused spur can only have one twin socket or one fixed appliance and a fused spur can have as many sockets as you require but care should be taken to ensure that the total load does not exceed the 13A fuse within the switched or unswitched-fused connection unit.

How long can a spur cable be?

The maximum length allowed for an unfused spur is 3m. The general rule of thumb, is that you can have an unfused spur at each socket, and one at the CU.

Can you spur off a junction box?

A spur comes off the ring circuit via a junction box, or more usually via an existing socket – which ever is easier. See also Adding a spur to a ring circuit from a socket. To install a spur from a junction box, you require a 30amp junction box. Locate the cable of the ring main as close to the new socket as possible.

Can I run a light off a ring main?

Running additional lights of ring main through fused spur is normally OK but not primary lights unless unless also emergency lighting is installed.

Can I do electrical work myself?

Replacements, Minor Repairs and ‘Like for Like’ Changes – These are the main electrical jobs that you’ll be allowed to undertake yourself. So, you might want to change and/or move sockets, ceiling lights or light switches. You can even look to change any wires that might look old or damaged.

What electrical work can I do myself Ireland?

Minor electrical works such as like-for-like replacements of switches and smaller features, moving light fittings without affecting the circuit or adding a socket or two to an existing circuit are all safe to do, once you understand the process at hand.

Do you need an electrician to change a light fitting UK?

No, however, you do need an electrician to install a new circuit, This may be the case if you are installing a light in a different location. If you are changing the electrics in high-risk areas, such as a bathroom, it is strongly advisable to have an electrician complete the work.